Machine class fit sheet
Will a miter saw station fit your garage?
A miter saw station (our planning allowance) measures 96 x 30 in (8.0 x 2.5 ft), runs on 120V at 15 A. It fits with operator room in 6 of our 6 garage sizes, the smallest being the 12x20 one-car, and it fits with a sedan parked inside from the 12x22 one-car up.
96 x 30 infootprint
n/aweight not stated
120V15 A
2 HPmotor
This sheet describes a class of machine. The footprint is our planning allowance, not a single product's measurement: check the dimensions in the listing of the machine you choose.
Fit in each garage size
| Garage | Alone, operator room | Car parked, working | Car parked, stored | Share of floor |
|---|---|---|---|---|
| One-car, 12 x 20 | yes | no | no | 8% |
| One-car, 12 x 22 | yes | yes | yes | 8% |
| Two-car, 20 x 20 | yes | yes | yes | 5% |
| Two-car, 22 x 22 | yes | yes | yes | 4% |
| Two-car, 24 x 24 | yes | yes | yes | 3% |
| Three-car, 32 x 24 | yes | yes | yes | 3% |
"Operator room" keeps 24 in clear around the machine, and "stored" drops that zone, for a machine you roll out only when the car is gone. Both leave a 24 in apron in front of the overhead door and a 30 in walk-around beside any parked sedan. In a 12 x 20 ft garage with a car inside, this machine has to be stored elsewhere.
Stock clearance
This is a stock-fed machine. For 8 ft boards it needs about 15 ft of clear line; the 12 x 20 bay offers 20 ft with nothing else in it and 22 ft in a 22 x 22. Where the bay is short, the answer is an outfeed support that folds away or a mobile base that rolls the machine to the open middle.
Electrical and moving it
- Circuit: 15 A at 120V on the planning allowance: a 20 A breaker and 12 AWG copper covers the 125 percent rule. On NEC Table 430.248 amps the same 2 HP motor comes to 30 A and 10 AWG on a 30 ft run. Have a licensed electrician confirm.
- Moving it: weight is not stated in our sources: read the listing, then size the base with the mobile base calculator.
Buy on Amazon
Prices change often; the button shows today's price on Amazon.
Moving and protecting it
Prices change often; the button shows today's price on Amazon.
Email me the buy list for a shop built around this machine
The machine, its base, its circuit parts and what goes beside it, as one list. Plus a few short emails, then a couple a month at most.
Unsubscribe anytime. You can also just read the checklist on this site.Where to see it placed
Other machine fit sheets
- 20 gallon air compressor
- 60 gallon air compressor
- mig welder 240v
- grizzly g1023rl cabinet table saw
- grizzly g0771z hybrid table saw
- grizzly g0962 open stand table saw
Frequently asked questions
Does the miter saw station fit in a one-car garage?
Yes, in a 12 x 20 ft one-car garage with no vehicle it fits with its operator zone clear and uses 8 percent of the floor. With a sedan parked inside it does not fit at all.
What circuit does the miter saw station need?
It draws 15 A at 120V (planning allowance), so a 20 A breaker with 12 AWG copper covers the 125 percent rule. On NEC table amps for 2 HP the circuit comes out to a 30 A breaker and 10 AWG copper over a 30 ft run. A licensed electrician confirms the circuit before you wire.
This page is researched guidance, not professional electrical, engineering or safety advice. Circuits, loads and clearances depend on your house, your service and your town: have a licensed electrician confirm any wiring, and check local code and each manufacturer's manual before you act.
