3 HP cabinet table saw
The 3 HP cabinet saw needs a 240V circuit. The Amazon pick is the nearest contractor-class alternative; check its listing for voltage, since the saving is only real if it runs on a circuit you already have.
Machine fit · Grizzly G1023RL
Will the Grizzly G1023RL fit your garage?
The Grizzly G1023RL measures 66 x 47 in (5.5 x 3.9 ft) and weighs 508 lb, runs on 240V at 14 A. It fits with operator room in 6 of our 6 garage sizes, the smallest being the 12x20 one-car, and it fits with a sedan parked inside from the 20x20 two-car up.
66 x 47 infootprint
508 lbship weight
240V14 A
3 HPmotor
From the grizzly.com listing: 32 in right rip, 3 in depth at 90 degrees, table 40 x 27, 34 in table height, base footprint 20-1/2 in square. Owner-rated 4.8 on grizzly.com (137 reviews).
Fit in each garage size
| Garage | Alone, operator room | Car parked, working | Car parked, stored | Share of floor |
|---|---|---|---|---|
| One-car, 12 x 20 | yes | no | no | 9% |
| One-car, 12 x 22 | yes | no | no | 8% |
| Two-car, 20 x 20 | yes | yes | yes | 5% |
| Two-car, 22 x 22 | yes | yes | yes | 4% |
| Two-car, 24 x 24 | yes | yes | yes | 4% |
| Three-car, 32 x 24 | yes | yes | yes | 3% |
"Operator room" keeps 30 in clear around the machine, and "stored" drops that zone, for a machine you roll out only when the car is gone. Both leave a 24 in apron in front of the overhead door and a 30 in walk-around beside any parked sedan. In a 12 x 20 ft garage with a car inside, this machine has to be stored elsewhere.
Stock clearance
This is a stock-fed machine. For 8 ft boards it needs about 16 ft of clear line; the 12 x 20 bay offers 20 ft with nothing else in it and 22 ft in a 22 x 22. Where the bay is short, the answer is an outfeed support that folds away or a mobile base that rolls the machine to the open middle.
Electrical and moving it
- Circuit: 14 A at 240V on the listing: a 20 A breaker and 12 AWG copper covers the 125 percent rule. On NEC Table 430.248 amps the same 3 HP motor comes to 25 A and 10 AWG on a 30 ft run. Have a licensed electrician confirm.
- Moving it: at 508 lb (shipping weight) a mobile base rated 670 lb or more is the minimum, for example the VEVOR Mobile Base.
- Delivery: machines this heavy usually arrive by freight on a pallet. Plan the path from the curb to the bay, the door width and who helps you lift.
Buy the G1023RL, or compare the Amazon pick
Same job, two ways to buy, with one line on when each wins.
Prices change often and Grizzly runs sales, so the buttons show current prices.
Moving and protecting it
Prices change often; the button shows today's price on Amazon.
Email me the buy list for a shop built around this machine
The machine, its base, its circuit parts and what goes beside it, as one list. Plus a few short emails, then a couple a month at most.
Unsubscribe anytime. You can also just read the checklist on this site.Compare the G1023RL head to head
Where to see it placed
Other machine fit sheets
- grizzly g0771z hybrid table saw
- grizzly g0962 open stand table saw
- grizzly g0555 14 inch bandsaw
- grizzly g0860 cyclone dust collector
- grizzly g0441 3hp cyclone dust collector
- grizzly g0945 benchtop jointer
Frequently asked questions
Does the Grizzly G1023RL fit in a one-car garage?
Yes, in a 12 x 20 ft one-car garage with no vehicle it fits with its operator zone clear and uses 9 percent of the floor. With a sedan parked inside it does not fit at all.
What circuit does the Grizzly G1023RL need?
It draws 14 A at 240V (listing), so a 20 A breaker with 12 AWG copper covers the 125 percent rule. On NEC table amps for 3 HP the circuit comes out to a 25 A breaker and 10 AWG copper over a 30 ft run. A licensed electrician confirms the circuit before you wire.
This page is researched guidance, not professional electrical, engineering or safety advice. Circuits, loads and clearances depend on your house, your service and your town: have a licensed electrician confirm any wiring, and check local code and each manufacturer's manual before you act.
