6 in benchtop jointer
Both are 6 in benchtop jointers. The Grizzly lists 1-1/2 HP and 22,000 cuts per minute; the Amazon pick has a spiral cutterhead.
Machine fit · Grizzly G0945
Will the Grizzly G0945 fit your garage?
The Grizzly G0945 measures 30 x 9.5 in (2.5 x 0.8 ft) and weighs 44 lb, runs on 120V at 10 A. It fits with operator room in 6 of our 6 garage sizes, the smallest being the 12x20 one-car, and it fits with a sedan parked inside from the 12x20 one-car up.
30 x 9.5 infootprint
44 lbunit weight
120V10 A
1.5 HPmotor
From the grizzly.com listing: 6 in width, 1/8 in depth of cut, table 6-1/4 x 30, base footprint 9-1/2 x 19-1/2, 2-1/2 in dust port.
Fit in each garage size
| Garage | Alone, operator room | Car parked, working | Car parked, stored | Share of floor |
|---|---|---|---|---|
| One-car, 12 x 20 | yes | yes | yes | 1% |
| One-car, 12 x 22 | yes | yes | yes | 1% |
| Two-car, 20 x 20 | yes | yes | yes | 0% |
| Two-car, 22 x 22 | yes | yes | yes | 0% |
| Two-car, 24 x 24 | yes | yes | yes | 0% |
| Three-car, 32 x 24 | yes | yes | yes | 0% |
"Operator room" keeps 24 in clear around the machine, and "stored" drops that zone, for a machine you roll out only when the car is gone. Both leave a 24 in apron in front of the overhead door and a 30 in walk-around beside any parked sedan.
Electrical and moving it
- Circuit: 10 A at 120V on the listing: a 15 A breaker and 14 AWG copper covers the 125 percent rule. On NEC Table 430.248 amps the same 1.5 HP motor comes to 25 A and 10 AWG on a 30 ft run. Have a licensed electrician confirm.
- Moving it: at 44 lb a mobile base rated 60 lb or more is the minimum, for example the WEN Mobile Base.
Buy the G0945, or compare the Amazon pick
Same job, two ways to buy, with one line on when each wins.
Prices change often and Grizzly runs sales, so the buttons show current prices.
Moving and protecting it
Prices change often; the button shows today's price on Amazon.
Email me the buy list for a shop built around this machine
The machine, its base, its circuit parts and what goes beside it, as one list. Plus a few short emails, then a couple a month at most.
Unsubscribe anytime. You can also just read the checklist on this site.Compare the G0945 head to head
Where to see it placed
Other machine fit sheets
- grizzly t34608 benchtop drill press
- grizzly g4000 metal lathe
- grizzly g0602 metal lathe
- grizzly g0704 mill drill
- grizzly g0408 wide belt sander
- grizzly g0738 hanging air filter
Frequently asked questions
Does the Grizzly G0945 fit in a one-car garage?
Yes, in a 12 x 20 ft one-car garage with no vehicle it fits with its operator zone clear and uses 1 percent of the floor. It also fits with a sedan parked inside.
What circuit does the Grizzly G0945 need?
It draws 10 A at 120V (listing), so a 15 A breaker with 14 AWG copper covers the 125 percent rule. On NEC table amps for 1.5 HP the circuit comes out to a 25 A breaker and 10 AWG copper over a 30 ft run. A licensed electrician confirms the circuit before you wire.
This page is researched guidance, not professional electrical, engineering or safety advice. Circuits, loads and clearances depend on your house, your service and your town: have a licensed electrician confirm any wiring, and check local code and each manufacturer's manual before you act.
