Benchtop table saw
The Amazon pick is a jobsite saw with a folding rolling stand you can stow against a wall; the Grizzly saw is a heavier variable-speed benchtop that stays on its bench.
Layout · Three-car, 32 x 24
Mixed shop with a car parked layout for a 32x24 three-car garage
A mixed shop with a car parked in a 32 x 24 ft garage: all 7 machines fit. 5 circuits on 120V, subpanel around 60 A, and 529 of 768 sq ft is aisle, operator zone and open floor rather than machine.
1. Jobsite table saw on a stand (32 x 26 in)2. 14 in bandsaw (25 x 18 in)3. Tool bench (Planer, Drill press) (60 x 28 in)4. Shop vac with cyclone separator (18 x 18 in)5. 4 ft workbench (48 x 24 in)6. Steel shelving unit (60 x 24 in)
machinebenchoperator zonevehicle
1. Jobsite table saw on a stand (32 x 26 in)2. 14 in bandsaw (25 x 18 in)3. Tool bench (Planer, Drill press) (60 x 28 in)4. Shop vac with cyclone separator (18 x 18 in)5. 4 ft workbench (48 x 24 in)6. Steel shelving unit (60 x 24 in)
machinebenchoperator zonevehicle
What fits in a 32x24 three-car garage for mixed shop with a car parked
| # | Machine | Footprint | Size source |
|---|---|---|---|
| 1 | Jobsite table saw on a stand | 32 x 26 in | planning allowance |
| 2 | 14 in bandsaw | 25 x 18 in | listing |
| 3 | Tool bench (Planer, Drill press) | 60 x 28 in | planning allowance |
| 4 | Shop vac with cyclone separator | 18 x 18 in | planning allowance |
| 5 | 4 ft workbench | 48 x 24 in | planning allowance |
| 6 | Steel shelving unit | 60 x 24 in | planning allowance |
| - | Hanging air filter (hangs from the ceiling) | 20 x 17 in | listing |
Every machine in this trade's package found a place on the floor.
Where the floor goes
| Item | Sq ft | Share |
|---|---|---|
| Garage floor | 768 | 100% |
| Vehicles parked inside | 198 | 26% |
| Machine and bench footprints | 41 | 5% |
| Aisles, zones and the door apron | 529 | 69% |
There is room to spare, so the next purchase can be a bigger machine rather than a smaller bay. Footprints are the machine's own size; the zones and aisles are why a garage "feels" smaller than the sum of its machines.
Can you actually rip an 8 ft board?
An 8 ft board through the jobsite table saw on a stand needs about 14 ft of clear line (the saw's depth plus about 1.5 times the stock). In this plan the clearest run is 3 ft with the vehicle out and 3 ft with it in: short with the car out, not with it in. The usual answers are an outfeed table that folds away, breaking sheets down outside with a track saw, or putting the saw on a mobile base and rolling it to the middle of the bay.
Mixed shop with a car parked notes for this bay
This plan only works because the machines roll. Park the car, keep everything compact against the back wall, and roll tools out to a working position when the car is gone.
In work mode, with the car out, the plan puts 6 of the machines in working positions and keeps the operator zones clear for all of them.
Living with the car
With 2 sedans parked inside, the vehicle takes 198 sq ft and its walk-around keeps another strip clear. Stored machines carry no operator zone in this plan, because you only run them when the car is out. Check each parked position against your car's door swing before you commit.
Circuits for this layout
| Circuit | Volts | Breaker | Wire | Receptacle |
|---|---|---|---|---|
| Jobsite table saw on a stand | 120V | 20 A | 12 AWG | NEMA 5-20R |
| 14 in bandsaw | 120V | 20 A | 12 AWG | NEMA 5-20R |
| Tool bench (Planer, Drill press) | 120V | 20 A | 12 AWG | NEMA 5-20R |
| Shop vac with cyclone separator | 120V | 20 A | 12 AWG | NEMA 5-20R |
| Shared bench circuit 1 | 120V | 20 A | 12 AWG | NEMA 5-20R (several) |
That is 5 circuits, about 22 A of demand after diversity, and a subpanel in the 60 A range to ask your electrician about. Sizes use NEC Table 430.248 for motor amps and Table 310.16 (60 C column) for wire; have a licensed electrician confirm. The workshop amps calculator lets you change the loads.
Which machines belong on mobile bases
| Machine | Weight we can state | Base rating to shop for |
|---|---|---|
| Jobsite table saw on a stand | not stated | check the machine weight first |
| 14 in bandsaw | 207 lb (listing) | 270 lb or more, e.g. WEN Mobile Base |
| Tool bench (Planer, Drill press) | not stated | check the machine weight first |
| Shop vac with cyclone separator | not stated | check the machine weight first |
The mixed shop with a car parked package for a 32x24 three-car garage: Amazon and Grizzly
One card per machine in the plan. Each shows the Amazon pick and the Grizzly Industrial pick for the same job.
14 in bandsaw
Both are 14 in, 1 HP saws that run on 120V. The Grizzly saw is the established cast-iron-table pick; the Amazon pick is dual-voltage and ships to your door.
4 ft adjustable workbench
Pick the Amazon bench for the lowest entry cost; pick the Grizzly bench if you want outlets built into the bench and a direct parts line.
Prices change often and Grizzly runs sales, so the buttons show current prices.
Rest of the shop: the small gear
Storage, bases and safety items for this layout.
Prices change often; the button shows today's price on Amazon.
Email me the buy list for this layout
Every machine, bench and base in this plan as one list you can keep, with the circuits it needs. Plus a few short emails, then a couple a month at most.
Unsubscribe anytime. You can also just read the checklist on this site.Size the systems for this garage
- Heater size for a 32x24 three-car garage
- Dust collector size for a 32x24 three-car garage
- Shop lighting for a 32x24 three-car garage
- Air filtration for a 32x24 three-car garage
- Mini-split size for a 32x24 three-car garage
- Subpanel for a mixed shop with a car parked
- 240V in a garage, explained
Fit sheets for the machines in this plan
Other trades and garage sizes
- Woodshop in a 32x24 three-car
- Machine shop in a 32x24 three-car
- Welding and fab in a 32x24 three-car
- Auto and mechanic in a 32x24 three-car
- Mixed shop with a car parked in a 12x20 one-car
- Mixed shop with a car parked in a 12x22 one-car
- Mixed shop with a car parked in a 20x20 two-car
- Mixed shop with a car parked in a 22x22 two-car
- Mixed shop with a car parked in a 24x24 two-car
Frequently asked questions
Can I fit a table saw in a 32x24 three-car garage with a car in it?
Yes: the plan places a jobsite table saw on a stand at 32 x 26 in with its operator zone clear. Ripping long boards still needs the car out or an outfeed that folds away.
What circuits does a mixed shop with a car parked need in a 32x24 three-car garage?
The machines in this plan need 5 circuits: 0 at 240V and 5 at 120V, which suggests a subpanel in the 60 A range. Have a licensed electrician confirm the service and the panel.
How much floor is left in a 32x24 three-car garage after a mixed shop with a car parked?
About 529 of 768 sq ft, 69 percent, is aisle, operator zone and door apron once Jobsite saw, Bandsaw, Tool bench, and Vac + separator and the rest are placed.
This page is researched guidance, not professional electrical, engineering or safety advice. Circuits, loads and clearances depend on your house, your service and your town: have a licensed electrician confirm any wiring, and check local code and each manufacturer's manual before you act.
