6 x 48 jointer on a cabinet stand
The long-bed floor jointer flattens longer boards than any benchtop. The Amazon pick is the benchtop alternative that fits a one-car garage.
Machine fit · Grizzly G0814
Will the Grizzly G0814 fit your garage?
The Grizzly G0814 measures 47.5 x 20 in (4.0 x 1.7 ft) and weighs 260 lb, runs on 120V at 14 A. It fits with operator room in 6 of our 6 garage sizes, the smallest being the 12x20 one-car, and it fits with a sedan parked inside from the 12x22 one-car up.
47.5 x 20 infootprint
260 lbship weight
120V14 A
1 HPmotor
From the grizzly.com listing: 6 in width, 1/8 in depth of cut, 1/2 in rabbet, table 6-5/8 x 47-3/8, 5000 RPM cutterhead, base footprint 13-1/2 x 18. Also wirable for 7 A at 220 V.
Fit in each garage size
| Garage | Alone, operator room | Car parked, working | Car parked, stored | Share of floor |
|---|---|---|---|---|
| One-car, 12 x 20 | yes | no | no | 3% |
| One-car, 12 x 22 | yes | yes | yes | 2% |
| Two-car, 20 x 20 | yes | yes | yes | 2% |
| Two-car, 22 x 22 | yes | yes | yes | 1% |
| Two-car, 24 x 24 | yes | yes | yes | 1% |
| Three-car, 32 x 24 | yes | yes | yes | 1% |
"Operator room" keeps 24 in clear around the machine, and "stored" drops that zone, for a machine you roll out only when the car is gone. Both leave a 24 in apron in front of the overhead door and a 30 in walk-around beside any parked sedan. In a 12 x 20 ft garage with a car inside, this machine has to be stored elsewhere.
Electrical and moving it
- Circuit: 14 A at 120V on the listing: a 20 A breaker and 12 AWG copper covers the 125 percent rule. On NEC Table 430.248 amps the same 1 HP motor comes to 20 A and 12 AWG on a 30 ft run. Have a licensed electrician confirm.
- Moving it: at 260 lb (shipping weight) a mobile base rated 340 lb or more is the minimum, for example the WEN Mobile Base.
- Delivery: machines this heavy usually arrive by freight on a pallet. Plan the path from the curb to the bay, the door width and who helps you lift.
Buy the G0814, or compare the Amazon pick
Same job, two ways to buy, with one line on when each wins.
Prices change often and Grizzly runs sales, so the buttons show current prices.
Moving and protecting it
Prices change often; the button shows today's price on Amazon.
Email me the buy list for a shop built around this machine
The machine, its base, its circuit parts and what goes beside it, as one list. Plus a few short emails, then a couple a month at most.
Unsubscribe anytime. You can also just read the checklist on this site.Where to see it placed
Other machine fit sheets
- grizzly g0459 drum sander
- grizzly g0548zp canister dust collector
- grizzly g0555xh resaw bandsaw
- grizzly t32337 quiet air compressor
- jobsite table saw
- benchtop planer
Frequently asked questions
Does the Grizzly G0814 fit in a one-car garage?
Yes, in a 12 x 20 ft one-car garage with no vehicle it fits with its operator zone clear and uses 3 percent of the floor. With a sedan parked inside it does not fit at all.
What circuit does the Grizzly G0814 need?
It draws 14 A at 120V (listing), so a 20 A breaker with 12 AWG copper covers the 125 percent rule. On NEC table amps for 1 HP the circuit comes out to a 20 A breaker and 12 AWG copper over a 30 ft run. A licensed electrician confirms the circuit before you wire.
This page is researched guidance, not professional electrical, engineering or safety advice. Circuits, loads and clearances depend on your house, your service and your town: have a licensed electrician confirm any wiring, and check local code and each manufacturer's manual before you act.
